APEX Super Cuelight Wireless Sound and Light Signal System 1000m Auto Cue

Description

Super Cuelight is a wireless sound and light signal system, it can use wireless remote control to send “Next page” ” Previous page” commands to the device, accompanied by Sounds and lights act as reminders.

Super Cuelight uses high data rate RF protocol to provide fast response for wireless transmission, strong anti-interference, can easily resist live light stick remote control, Light-emitting bracelet controller, radio and other wireless signal interference, long transmission distance. Unobstructed effective control distance of more than 1000 meters. Remotely available via USB Control the demo application.

You can use network cable and XLR cable cascade multiple devices  to ensure the consistency of multiple devices

Model:

Packing List

◆Master 1PC

◆Remoter 2pcs

◆USB-A to USB-B 4PCS

◆ User manual 1pc

◆ Power Adapter 1pc

◆ Charging Cable 2pcs

Super Cuelight Function description

1. Local Control

►[Next page] 、●[Turnoff the screen]、◄ [Previous page]

2. MASTER & SLAVEswitch

MASTER (Set MASTER) 、 SALVE (Set SALVE)

NOTE: When multiple devices are connected by wire, set the one closest to the remote as

master, set the others as slaves so that only the master receives the signal from the transmitter.

3. SOUND switch

Control speaker volume: HI (high volume), LO (low volume), OFF (off)

4. LIGHT switch

Control brightness: HI (highlight), LO (low light), OFF (off)

5. USB 1& 2&3&4

Without restarting, connect or disconnect the USB, remote control demoSoftware.

A total of 4 computers can be connected at the same time. Driver free support for MAC OS and WINDOWS system. Plug and play

6. USB Port

For direct connection with the computer, the computer can supply power to

the equipment.Device transmitting modeMimic keyboard commands “Next page”,

“Turn off Screen” and “Previous page”, thus preserving Leave mouse function.

7. RJ45 port

Devices are interconnected using network cables. For simultaneous control of

two receivers.    Cannot connect to the network switches!!

8. Output 3.5mm headphone Port

The stereo jack output corresponds to “Forward”, “backward” and “black screen” sound effects.

9. Code matching mode between remote control and receiver:

1: Code pairing adopts digit code pairing (different from traditional code pairing). Stick a small sharp object in the back of   the receiver a separate small Hole (click for 1 second). At this time the front panel “*” indicator light will light up, 8 seconds by the remote control of the laser key, “*” indicator light will flash twice, that is, the code success. The receiver then needs to be powered off and back on.

2: Often press the hole at the back of the receiver for 30 seconds, you can clear the remote control code stored inside the machine

11. Note:

Each USB port is an independent system, so, the first time to use, need to wait a few seconds,    waiting for the system With the page changer and the system matching completed, can be used, The second time to use it is not needed.!

12. If all accessories are lost, please contact the after-sales service free of charge

(* Please do not disassemble the receiver enclosure without permission, otherwise it will cause damage to internal components. If the components caused by disassembling the enclosure and motherboard without  permission are damaged, there is no warranty)

General operating instructions

1. Take out the receiver, remote control and USB cable
2. Adjust the rotatable antenna so that the antenna faces upward or at other angles that are convenient for receiving signals. Generally, there is no obstruction between the antenna and the remote control and the higher the antenna position, the better.
3. Connect the USB square plug to any USB port of the receiver and the USB flat plug to the computer
4. After the USB connection is successful, the corresponding port indicator light is red, and after the USB connection is disconnected, the indicator light goes out;
5. Press the remote control button or the page turning button on the receiver panel to turn pages. The next page corresponds to the yellow light dot matrix, and the previous page corresponds to the red dot matrix. There will be animation instructions when turning the page.

Remote control charging instructions

The remote control has a built-in lithium battery, which can effectively reduce the environmental pollution caused by disposable batteries.

1. The remote control supports external direct 2.5mm DC port charging, just take out the charger and plug it in directly